Skip to main content

punching unit notching tool hole

ips Werkzeugtechnik GmbH

Search form

Hauptmenü

  • .
  • ips-Werkzeugtechnik
    • Consulting and Engineering
    • Contact / Imprint
    • International contacts
    • Mission and experiences
  • Modular components
    • Press-operated tool units
      • Punching unit, hole Ø 2–7 mm
      • Punching unit, hole Ø 2-13 mm
      • Punching units, hole Ø 8-25 mm
      • Punching units, hole Ø 25-40 mm
      • Punching units, hole Ø 40-63 mm
      • Punching units, hole Ø 63-100 mm
      • Punching units, hole Ø 2-13 mm
      • Punching unit, hole Ø 8-22 mm
      • Punching unit, hole Ø 22-38 mm
      • Punching unit, hole Ø 35-63 mm
      • 90° notch units, notch size 63x63 mm
      • 90° notch units, notch size 125x125 mm
      • Rectangle notch units 50x50 mm
      • Rectangle notch units 100x75 mm
      • Radius cut unit, R 3–16 mm
      • Radius cut unit, R 3-20 mm
      • Cut-off units, cutting width 125 mm
      • Cut-off units, cutting width 250 mm
    • Pneumatic and hydraulic table presses
      • Pneumatic table presses 40 kN
      • Pneumatic table presses 80 kN
      • Hydraulic punching units, double-action 68 kN
      • Hydraulic table-presses, double-action 109 kN
    • Pneumatic and hydraulic tool units
      • Pneumatic punching units, single-action
      • Hydraulic punching units, double-action
      • Pneumatic and hydraulic profile punching units, single- and double-action
      • Pneumatic and hydraulic 90°-notch units, 63x63 mm
      • Pneumatic and hydraulic rectangle notch units
      • Mobile pneumatic punching and notch units
      • Pneumatic cut-off unit, 125 mm
      • Pneumatic and hydraulic 90° radii cutting units, R5-30mm
      • Pipe punching unit
    • Punches · dies · reduction bushes · strippers
      • Round hole punching tools
      • Shaped hole punching tools
      • Reduction bushes and sockets for round hole punching tools only
      • Shaped cut conversion kits
      • Compensating washers
      • Strippers
    • System extensions
      • Guide elements for series punch installation
      • Frames
      • Universal limit stop and workpiece support
      • Coordinate limit stop
      • Cylinder position monitoring device
      • Pneumatic pedals
      • Pneumatic power cylinder, single-action
      • Hydropneumatic power cylinder, double action
      • Hydraulic short-stroke cylinder, double-action
      • Hydraulic block cylinder, double-action
      • Hydraulic units
    • Small presses
      • Manual lever presses
      • Toggle presses
      • Rack presses
      • Pneumatic toggle presses
      • Direct-acting pneumatic presses
      • DAF direct-acting press cylinders
      • MicroPress wirh square ram
      • Hydropneumatic presses
      • Sliding tables
      • TPC-MIDI process monitoring
      • Press & Tool Concept
      • KP manual toggle presses
      • KP pneumatic presses
      • Tool systems
  • Special machines
    • Units • Machines
      • Punching of vehicle registration numbers
      • Serial punching unit for mist collectors
      • Punching of the inside lining
      • Punching unit for solar profiles
      • Unit for punching 3m long profiles
      • Special unit (20 x 4 m) for the processing of solar profiles
      • Punching unit for D-column covering
      • Punching the tank cap cutout in the mudguard
      • Punching unit for cutting hole profiles in the inside roof lining of vehicles
    • Presses • Specialunits
      • Electrically operated punching press
      • Pressing tool for solenoid valve
      • Special press unit for notching, pulling and cutting
      • Special hydraulic unit for bending wires
      • Press unit for punching round blanks
      • Steel cable with pressing bush
      • Trailer coupling recess in the rear bumper
  • Contract Manufacturing

Languages

  • English English
  • Deutsch Deutsch

Submenue

  • Contact

You are here

Home » Modular components » Press-operated tool units
  • Radius cut units, press-operated

Radius cut unit, R 3–16 mm

Radius cut unit, R 3–16 mm
Eckdaten
Radius range: 
3 - 20 mm
Cutting angle: 
max. 180 °
Material thickness: 
max. 6 mm
Series: 
605
Order number: 
WMP-0000-00B1
  • Press-operated
  • Radiuscutunits

 

ips catalogue, page 63
 Find this information in our ips catalogue, page 63  Download catalogue in PDF format
 

Your enquiry regarding product

Modular components

  • Press-operated tool units
    • Punching unit, hole Ø 2–7 mm
    • Punching unit, hole Ø 2-13 mm
    • Punching units, hole Ø 8-25 mm
    • Punching units, hole Ø 25-40 mm
    • Punching units, hole Ø 40-63 mm
    • Punching units, hole Ø 63-100 mm
    • Punching units, hole Ø 2-13 mm
    • Punching unit, hole Ø 8-22 mm
    • Punching unit, hole Ø 22-38 mm
    • Punching unit, hole Ø 35-63 mm
    • 90° notch units, notch size 63x63 mm
    • 90° notch units, notch size 125x125 mm
    • Rectangle notch units 50x50 mm
    • Rectangle notch units 100x75 mm
    • Radius cut unit, R 3–16 mm
    • Radius cut unit, R 3-20 mm
    • Cut-off units, cutting width 125 mm
    • Cut-off units, cutting width 250 mm
  • Pneumatic and hydraulic table presses
  • Pneumatic and hydraulic tool units
  • Punches · dies · reduction bushes · strippers
  • System extensions
  • Small presses

What we do

  • Consulting / Construction
  • CE mark with risk analysis in accordance with the EC Machinery Directive 2006/42/EC.

Our products

  • Tool units (press-operated)
  • Table presses (pneumatic and hydraulic)
  • Tool units (pneumatic and hydraulic)
  • Accessories for tool units
  • System extensions (frames, power cylinders, ...)
  • Small presses

Individual production units

  • Units • Machines
  • Presses • Special units

Company

  • Contact / Imprint
  • Data Protection Statement
  • Guiding principle and experiences
  • Blog